What Is Water Conductivity
The conductivity of water represents its ability to conduct an electric current. It is important to note that in its pure state, water does not conduct electricity. To be a conductor, water must have some cations and anions that will allow the transfer of energy.
Knowing this, you can understand that water with a high conductivity is also highly concentrated in total dissolved matter.
The unit of measurement used to express the conductivity of a water sample is Siemens per centimetre (S/cm) or microsiemens per centimetre (µs/cm). The expression µs/cm can be expressed in ppm to make it easier to understand. In fact, some conductivity meters calculate this automatically. To put things in perspective, a microsiemens represents the electrical conductivity equal to 1/1,000,000 of Siemens.
The Siemens is a unit of measurement in the international system of units. When expressed in terms of alternating current, the Siemens represents the reciprocal relationship between impedance and ohms. For direct current, the Siemens represents the reciprocal relationship between resistance and ohms.
Before going any further, let's remember that the conductivity of water is affected by the type and quantity of ions in the water. Indeed, the type of ion found in a body of water will have an impact on the conductivity since some materials are better conductors than others. As for the quantity, it is logical to think that the more conductors there are, the higher the conductivity. Finally, the temperature of the water will have a proportional impact on its conductivity. Basically, increasing the temperature of the water increases the solubility of the minerals and the mobility of the ions in it. This is the reason why an increase of 1°C can represent an increase of 2 to 4% of the conductivity.
What Are Total Dissolved Solids
Total dissolved solids (TDS) are organic and inorganic contaminants that can be found in water naturally or not. Since they are the source of conductivity, it is important to note that they are both cations and anions. Among the cations most often found in Canadian waters in dissolved form, we find calcium, magnesium, sodium and potassium. Anions include carbonate, bicarbonate, chloride, sulphate and nitrate.
Briefly, the materials dissolve in water through soil erosion, runoff or decomposition of flora. Since the covalent bonds of water molecules (H2O) are stronger than the ionic bonds of these contaminants, the water molecule breaks the bonds between them. Once these bonds are broken, the water molecules, which have a special polarity, surround the ions.
Is Water Conductivity Hazardous to Health
To answer quickly, the answer is no. As stated above, the conductivity of water represents the total dissolved solids concentration in the water. Since TDS generally represents minerals, it is not harmful to human health. On the other hand, water with total dissolved solids is prone to present particular odours, unattractive colours and particular tastes.
Finally, it is important to specify that although in general the consumption of water with any conductivity does not present a health risk, there are obviously exceptions. Continually consuming these contaminants can generate an excess in certain minerals and impact your body in various ways. Moreover, it is recognized that concentrations of total dissolved solids exceeding 1000 mg/l or 1000 ppm are not suitable for human consumption.
Why Is Monitoring Conductivity Important
In general, water conductivity does not pose a hazard to water treatment equipment. However, for some specific uses such as high-pressure boiler water or microprocessor production, conductivity can be problematic and can cause problems for equipment or products.
For example, for high-pressure boilers, the presence of total dissolved solids, indirectly from conductivity, can lead to the creation of foam in the boiler. If the boilers provide turbines, the foam can promote the formation of residues on the turbines. This can affect the efficiency and safety of the equipment.
- By the way, to learn more about water treatment systems for industrial boilers, we invite you to look at this article:
Next, it is important to remember that salt water has a high conductivity since salt ions are good conductors. Therefore, if the conductivity of your water is caused by the presence of salt, your equipment can pay the price since the presence of salt can accelerate the corrosion of the systems.
How to Reduce Water Conductivity
Knowing that the conductivity of water comes from the ions in it, it is obvious that the extraction of these ions will have an impact on the conductivity. Therefore, in order to achieve a target conductivity, the water must be treated by removing the conductive contaminants in the water.
Nanofiltration
Nanofiltration is a separation technique that works by using a physical barrier (filter) to block certain contaminants in the water. Nanofiltration membranes have 0.001 micron pores, which allows these filters to remove bacteria, viruses, minerals and even some salt ions.
Without going into superficial details, nanofiltration requires a physical barrier and pressure to force water through the pores of the membrane(s) to work. Nanofiltration will have an impact on conductivity since it has the ability to extract dissolved materials from the water. Due to their variable size, some ions cannot be extracted by using nanofiltration. This is why, typically, the use of this technology will allow the reduction of about 50 to 70% of the conductivity of the water.
Moreover, depending on the quality of the water you are dealing with, filtration steps may be necessary before nanofiltration since water with too many contaminants will clog the membranes too quickly and reduce the effectiveness of the treatment.
Reverse osmosis
Reverse osmosis is probably the most versatile water treatment technology available. The principle of osmosis is very similar to that of nanofiltration. The difference is the type of membrane used to separate the contaminants. In a simplified way, the difference between reverse osmosis and nanofiltration is the size of the pores. Indeed, the pores found on osmotic membranes have a size of 0.0001 microns.
- Since Reverse Osmosis is a complex and very popular technology, we have prepared an article presenting this technology in detail! Go to this page to learn more!
When reverse osmosis is used for conductivity reduction, the principle is the same as that of nanofiltration: to extract dissolved matter from the water. In contrast to nanofiltration, reverse osmosis allows the extraction of approximately 90-95% of the conductivity in the water. To achieve 95% conductivity removal, double reverse osmosis may be required.
Again, unless the feed water is particularly pure, reverse osmosis cannot usually be used alone or the membranes will foul too quickly. Typically, the concentration limit for total dissolved solids in water to be treated by RO is 70,000 ppm. When the TDS concentration is higher than 70,000 ppm, the osmosis membranes will clog up much too quickly.
To achieve a higher extraction rate than that offered by reverse osmosis, it is necessary to use polishing techniques, which are technologies installed downstream of an osmosis to extract the recalcitrant residues in the water.
Electrodeionization
Operating on the principle of ion exchange, electrodeionization is a polishing technique that works by producing a continuous electric current to continuously regenerate a resin bed. When water comes in contact with this current, it breaks down to form one H+ molecule and one OH- molecule. These molecules are responsible for the regeneration of the anionic and cationic resin in the EDI module.
The principle of ionic exchange remains the same, the contaminating ions are exchanged for ions allowing the production of pure water. When contaminated water passes through the resin bed of an electrodeionization module, the H+ and OH- ions on the resin are exchanged for the contaminant ions in the water, producing ionically pure water.
Electrodialysis Reversal
Operating on the principle that "opposites attract," electrodialysis reversal allows precise control of the total dissolved solids concentration in the water. Inside the electrodialysis modules are two electrodes and ion exchange membranes. The membranes are placed in such a way that they alternate between membranes that allow the removal of anions and cations.
The electrodes emit a current to attract ions to them. The anode attracts the anions, and the cathode attracts the cations. Thus, influenced by the electrical current, the ions travel to the electrodes and are blocked by the ion exchange membranes. In order to avoid membrane fouling, the polarity of the electrodes alternates several times per hour and reverses the direction of the ions.
Although there are several advantages to the use of EDR (electrodialysis reversal) modules, the fact that by adjusting the intensity of the current emitted inside the module, the total dissolved solids concentration can be adjusted is probably the most important.
However, it should be noted that the use of electrodialysis does not allow the extraction of all dissolved solids from the water. In general, each module will remove approximately 40-50% of the TDS present in the water. It may be necessary to install several EDR modules in series to achieve the desired conductivity. However, it is recognized that it is not cost-effective to have more than three EDR modules installed in series.
Ion-Exchange Vessels
Media filters are a type of treatment where water is passed through some type of media to remove contaminants. Although there is a wide variety of media available, for conductivity reduction, only media that allow ion exchange can be used.
To ensure proper conductivity reduction with ion-exchange vessels, the system must be done in stages, i.e., a separate bed ion exchanger. To start with, in order to avoid the clogging of the media, the larger ions, which are the anions, must be removed. Therefore, an anionic media bed is installed to reduce the anions. Next, a cationic media bed is installed to extract the cations. Finally, to complete the treatment efficiently, the water passes through a mixed resin bed.
Before going any further, we believe it is important to specify that ion exchange is a permutation process of positive or negative ions in order to modify the ionic composition of the aqueous solution subject to treatment. It is carried out thanks to acid or basic radicals that are found in the molecular structure of the resin and that allow an exchange between those found in the liquid to be treated and those found on the resins.
Unless the water is of very good quality, this type of treatment is generally not used individually. Rather, it is a polishing technique to minimize the presence of dissolved material in the water.
A Few Scenarios
In order to help you identify an optimal solution for your needs, we will present three situations. In the first situation, the water needs will be less than 20 gpm. The second will be for needs between 20 and 500 gpm and the third will be for needs over 500 gpm.
In each of these situations, two water qualities are presented: less than 50 µs/cm and less than 5 µs/cm.
Less than 20 gpm
For the production of 20 gpm or less of water with a conductivity of less than 50 µs/cm, reverse osmosis is generally suggested. As for the pre-filtration required for your osmosis, this will vary depending on your feed water and will not be covered in this article, but we invite you to visit this page to learn more about different primary filtration technologies.
If you require higher quality water, the best option is to add a resin bed ion exchanger. In this situation, there are two options for this type of technology. You can have a complete separate bed ion exchanger system installed or, if you have a service provider nearby, you can opt for a "DI Service" option. These services usually consist of tank rental, resin rental and resin regeneration. The advantage is that you don't have to worry about managing the risk of storing the hazardous materials used for regeneration, and the associated costs are generally advantageous given the small amount of water required for your operations.
- To learn more about our regeneration services, we invite you to visit our website: here.
In short, whether you opt for the complete installation of a system or the DI service option, these two technologies together will allow the production of water with a conductivity of less than 5 µs/cm.
20 Gpm to 500 Gpm
Again, here, for the production of water with a conductivity of less than 50 µs/cm, the use of reverse osmosis alone would be ideal. However, for the production of water with less conductivity, at this flow rate, the resin bed ion exchanger would not provide. Therefore, a combination of reverse osmosis + EDI should be chosen.
By adopting electrodeionization, the conductivity of the water will be below 5 µs/cm. Although the initial financial investment will be higher, the long-term profitability will be much more profitable and due to the low operating costs of the EDI modules.
500 Gpm and More
For the production of 500 gpm of water and more, it is always the same principle. For a conductivity of less than 50 µs/cm, reverse osmosis alone is still the best choice. On the other hand, for water production of less than 5 µs/cm, we go back to resin bed ion exchangers. However, in this situation, the installation of a complete system with separate bed resins and regenerators will be necessary since the equipment becomes too massive to be transported economically.
Nanofiltration and EDR Modules
As you may have noticed, these suggestions do not include the two technologies mentioned above. This is because nanofiltration offers essentially the same type of treatment as reverse osmosis, but in a less efficient manner. This technology could be prioritized when the targeted conductivity is between 50 and 100 µs/cm.
As for electrodialysis inversion, these modules have been designed for specific uses where the concentration of suspended solids is very high. In addition, they are very popular when conductivity must be reduced without affecting the presence of certain "contaminants" in the water. For example, they are widely used in municipal wastewater management where there is no need to extract chlorine for water disinfection.
Although electrodialysis reversal modules are very expensive, the operating costs are generally attractive since no membrane needs to be changed and the energy required to operate them is relatively low.
TDS and conductivity, a history of the past
Let's recall that the conductivity of water is caused by the presence of dissolved matter in it since pure water does not conduct electricity. The technologies allowing the reduction of the conductivity are very varied. We have presented the most common and effective ones.
No matter what your water production goal is, achieving it is not a problem. What can be challenging is identifying the best solution for your needs. Selecting the wrong technology will not prevent you from lowering the conductivity of the water. However, the cost and profitability of your equipment will be greatly affected.
Anyway, we hope you have found answers to your questions in this article. If you have further questions, we invite you to read the rest of our blog posts, visit our FAQ or write to us directly.